Products

  • 0
  • 0

Influence of Concrete Foaming Agent on Foam Concrete (2)

Recently, covid 19 outbreak spreads in Shanghai, China. There are more than 25,000 new asymptomatic domestic infections every day. China is implementing a dynamic zero-out policy. A leading respiratory expert said the key to COVID-19 prevention and control is to minimize transmission and fatality rate. Omicron has a low case fatality rate but is highly transmissible and can still claim many lives in large outbreaks. "Total openness is not applicable in China.  For China, we should keep to the dynamic zero-out and gradually open up."  

However, "dynamic zero clearance" is not the pursuit of complete "zero infection".  As the Novel Coronavirus has its own uniqueness and strong concealment, there may be no way to prevent the detection of cases at present, but rapid detection and prompt treatment must be carried out, as soon as one case is found, one case will be dealt with.  

The situation in Shanghai is serious. As the financial center of China, Shanghai is a very important city, and the outbreak of the epidemic in Shanghai will put a great impact on China's economy.  The current task is to contain the spread of the epidemic as soon as possible, to achieve social zero so that Shanghai's life and economy quickly return to normal.  

As China plays an important role in the global supply chain, the outbreak will have a significant impact on the supply and prices of many concrete foaming agent.

3. The larger the bubble diameter, the better, should be more than 1mm 

The pore diameter should be the same as the bubble diameter. Some experts misleading the pursuit of a small foam aperture of 0.1mm, in fact, because of physical foaming if the bubble diameter is large, the stability of the foam cannot be made of foam concrete. The same raw material and formula, the same equipment and technology, just change the bubble diameter, the compressive strength of 1mm bubble diameter of foam concrete, then 0.1mm bubble diameter of foam concrete, at least 20% higher. Therefore, it is wrong to pursue a bubble diameter of more than 0.1mm, which should be corrected in the production of foamed concrete.

 

4. The lower the foam bleeding rate, the better. Avoid using milk foam.

According to the size of water content, foam is divided into milk foam with more water and sponge foam with more water. Among them, lacteal foam is unqualified inferior foam and cannot be used.

After the foam is made, it gradually secretes water. Its secreting water includes two parts: 

Bleeding of foam liquid film. This water is secreted from the liquid membrane, which is secreted by the liquid membrane under the combined action of gravity drainage, surface tension drainage, and liquid membrane damage drainage. The thicker the liquid film of foam is, the larger the bleeding is. The faster the bubble burst, the more bleeding.

Water between bubbles. This is the water that didn't form the bubble film. The worse the foaming agent and foaming machine’s foaming performance, the more water between bubbles cannot form foam liquid film. They're essentially water that doesn't bubble.


When the foam is bleeding at a high rate, it becomes as thin as float juice, sloshing around and not piling up, and there's a lot of water in the foam. When this foam is added to the cement slurry, the cement slurry becomes very thin, and the foam is very little, the volume of the slurry is small, and the resulting foam concrete density is very high, not technical requirements. 

 

Therefore, latex foam should not be used. The appearance of a technically acceptable foam should be a spongy, compact bubble, piled up like white clouds, like bouncing cotton, and not sloshing. This foam has very little water content. This shows that its foam liquid film is small, the foam is not easy to burst, there is little water between the bubbles, and the amount of bubbles is large, accounting for most of the volume of bubbles. It should be emphasized here that the spongy foam must be a small bubble with a diameter of less than 1mm, rather than a few millimeters, or even dozens of millimeters. Bullae are easy to pile up, also like white clouds, but because of the large diameter of the bullae, also unqualified. 

 

The low secretion of foam is mainly to ensure the number of bubbles in the foam and the porosity of foamed concrete, that is, to ensure the density of foamed concrete. 

 

5. The foam has no side effects on cementitious materials 

The cementitious material is the main source of strength of foamed concrete, the addition of foam cannot affect its cementitious property, that is, there is no negative cementitious effect. Not every bubble can achieve this.

In the long-term test, we discover a lot of foam to cement, magnesite, gesso of gelling have hindrance, can reduce the strength of foam concrete, sometimes even from beginning to end the concrete after hardening loses strength basically, resemble a dish scatters sand.  The stability of these foams is very good, several hours do not disappear, the appearance of sponge, bleeding is very low, dense, and uniform, all aspects meet the technical requirements, but are not compatible with the gel material, so cannot be used for production. This means that foams that are otherwise qualified, such as affecting strength, are ultimately not technically qualified. 

 

Suppliers of Concrete Additives

TRUNNANO is a reliable foaming agents supplier with over 12-year experience in nano-building energy conservation and nanotechnology development.

If you are looking for high-quality CLC foaming agents, please feel free to contact us and send an inquiry. (sales@cabr-concrete.com)

We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.


3D printing technology emerged in the mid-1990s and is actually the latest rapid prototyping device utilizing technologies such as light curing and paper lamination. It is basically the same as ordinary printing. The printer is equipped with "printing materials" such as liquid or powder. After connecting to the computer, the "printing materials" are superimposed layer by layer through computer control, and finally the blueprint on the computer is turned into a real thing. This printing technology is called 3D stereo printing technology.
Our company is a strong company that provides excellent 3D printing concrete foaming agent. If you need 3D printing and concrete foaming agent, please feel free to contact us.

Inquiry us

Our Latest Products

How is Niobium Carbide NbC powder produced?

Niobium carbide (NBC and Nb2C) is a very hard refractory ceramic material, widely used in refractory high temperature materials and cemented carbide additives.…

Application of Nitinol Powder

Nitinol is a shape memory alloy, a special alloy that can automatically restore its plastic deformation to its original shape at a certain temperature. It can meet the needs of various engineering and medical applications and is an excellent function…

Description of zinc stearate

The zinc stearate liquid is called zinc stearate emulsion. It has a wide range of applications and can be used as a release agent, color retention agent,…